I have an Exchange 2013 CU1 that I have setup many receive connectors up for but seem to have a problematic one in particular.
The setup is to allow anonymous (yes I have run the ADD-ADPermission cmdlet) and is restricted down to the one IP for the remote host receive information. This is required due to the nature of the application I am using on the remote PC.
So, the error that comes up is a typical error:
530 5.7.1 Client was not authenticated
Also, I can telnet into the Exchange Server and get the same failure after the mail from: my@emailaddress.com
So, to fix this, I have to disable the receive connector in the ECP, wait a little while (a minutes or so) and then enable. I can now use the application to send logs via mail and also get all the expected responses and completed telnet session to send mail.
This isn't a suitable workaround as I only receive a small portion of the logs before the system falls over and I have to repeat the process again.
Here is my Receive connector config. Thanks in advance
PSComputerName : myserver.net
RunspaceId : c5ca7f81-e502-4453-ab52-27d6b44fe614
PSShowComputerName : False
AuthMechanism : None
Banner :
BinaryMimeEnabled : True
Bindings : {0.0.0.0:25}
ChunkingEnabled : True
DefaultDomain :
DeliveryStatusNotificationEnabled : True
EightBitMimeEnabled : True
BareLinefeedRejectionEnabled : False
DomainSecureEnabled : False
EnhancedStatusCodesEnabled : True
LongAddressesEnabled : False
OrarEnabled : False
SuppressXAnonymousTls : False
ProxyEnabled : False
AdvertiseClientSettings : False
Fqdn : myserver.net
ServiceDiscoveryFqdn :
TlsCertificateName :
Comment :
Enabled : True
ConnectionTimeout : 00:10:00
ConnectionInactivityTimeout : 00:05:00
MessageRateLimit : Unlimited
MessageRateSource : IPAddress
MaxInboundConnection : 5000
MaxInboundConnectionPerSource : 20
MaxInboundConnectionPercentagePerSource : 2
MaxHeaderSize : 128 KB (131,072 bytes)
MaxHopCount : 60
MaxLocalHopCount : 12
MaxLogonFailures : 3
MaxMessageSize : 35 MB (36,700,160 bytes)
MaxProtocolErrors : 5
MaxRecipientsPerMessage : 200
PermissionGroups : AnonymousUsers, Custom
PipeliningEnabled : True
ProtocolLoggingLevel : None
RemoteIPRanges : {xxx.xxx.xxx.xxx}
RequireEHLODomain : False
RequireTLS : False
EnableAuthGSSAPI : False
ExtendedProtectionPolicy : None
LiveCredentialEnabled : False
TlsDomainCapabilities : {}
Server : MYSERVER
TransportRole : HubTransport
SizeEnabled : Enabled
TarpitInterval : 00:00:05
MaxAcknowledgementDelay : 00:00:30
AdminDisplayName :
ExchangeVersion : 0.1 (8.0.535.0)
Name : Allow relay from MYSERVER
Groups,CN=company Ltd,CN=Microsoft
Guid : 1186dca7-7372-47f7-a950-fd1ac490cfc8
ObjectCategory : domain.net/Configuration/Schema/ms-Exch-Smtp-Receive-Connector
ObjectClass : {top, msExchSmtpReceiveConnector}
WhenChanged : 6/19/2013 1:49:06 PM
WhenCreated : 6/13/2013 5:09:27 PM
WhenChangedUTC : 6/19/2013 1:49:06 AM
WhenCreatedUTC : 6/13/2013 5:09:27 AM
OrganizationId :
OriginatingServer : MYDC.domain.net
IsValid : True
ObjectState : Unchanged